1, insulation, fire-retardant insulation, water proof one board with excellent thermal insulation properties, low thermal conductivity and stability, independent of temperature, humidity changes and impact, but has to stop flooding, moisture infiltration characteristics, but also to avoid condensation inside the material due to water, due to thawing and split up the expertise. By state authorities XPS board fire rating to B2 level and above, fiberboard roof panel as A level non-combustible materials, with walls consisting of refractory limit is much higher than the national standard. 2, lightweight, high strength, excellent and fast construction wall insulation decorative one board, much lighter than the other curtain wall plate with the area under its impact resistance: no cracking, peeling, through (CNS 13778). Not only reduce the burden on the building, but also significantly reduce the security risks. The use of an adhesive and anchor combination, to prevent the finish layer and the inner liner plate or insulation peeling risks, greatly improved the production of security, simplified construction process, fast installation, shorten the construction period, and also a substantial reduction of the quality problems, safety hazards. 3, beautiful decoration, durable and stable one plate of factory standardized production, from the modern lines of the finished board, eliminating the external environment and artificial factors of adverse effects on the wall decoration. Decorative surface using fluorocarbon, and other water-based metallic paint, rich colors, stable and consistent results. So as to solve the walls cracking, paint color, easy to dirty walls and other problems encountered in the past construction. Adhesive and anchor combination, to ensure the stability of the product installation safety and decorative effect, decorative effect one plate decorated with any artisanal decorative systems can not match, only this characteristic, it is sufficient to fully replace the traditional aluminum, aluminum panels, stone and paint. 4, high-end decorative, cost-effective mechanization of all sheet factory clean room production, prefabrication, stable performance, good weather resistance. No on-site spray directly on the wall. ? Decorative composite insulation board, durable, beautiful and stylish, you can create a simulation marble, aluminum and other fluorocarbon different effects. Excellent insulation properties, it is fully in line with the national energy conservation standards. ZFM board can be widely used in high-end residential, office buildings, villas, houses landscape decoration insulation. ? ?? Installation process: The base of claim 1. insulation decorative plate special layered structure, to ensure that the insulation decorative board itself strong and smooth. When properly installed insulation decorative plaster board substrate should be up to standard, no crack, powder can not afford, can not afford to sand, not hollowing, no peeling, smooth surface, vertical elevation, the vertical angle of yin and yang. Since the primary wall is slightly uneven and rough it can be adjusted by special mortar, so that the grassroots of insulation decorative plate flatness and finish relatively low and relatively simple process. This metallic paint, fluorocarbon paint and other high-grade imitation aluminum in order to achieve the effect, at the use of procedures to deal with a dozen grassroots stark comparison. 2. Paste the insulation decorative plates for light board, the product is only 8-10 kg of weight per square meter, compared to the overall weight of field operations country EPS / XPS thin plaster systems is still small, so only special mortar paste it directly to the wall, you can achieve the required bonding strength requirements. 3. The anchor for the total elimination of insulation decorative board delamination, and enhanced insulation decorative plate overall security, the use of anchors, fastening facing layer and the insulation decorative board and be securely attached to the wall again. This duplex fixed mode, the high-rise building facade decoration provides complete protection. 4. seams when handling insulation decorative panels installed in the field between the two plates reserved 5mm-10mm wide seams. When finished plate at the bottom of a dry mortar in the joints in the foam filling them, and then weather sealant fill flat strip joints. Insulation Decorative Security Editor finished board insulation decorative integration of a variety of ways to ensure the security of the system: 1, the use of high-end composite materials, ensure firm adhesion liner insulation board with top and bottom surfaces, insulation board and reinforcing layer; 2, using a special adhesive mortar configuration, which far exceeds the strength of the bond strength of traditional exterior insulation adhesive mortar; 3, the use of high-strength metal anchors, providing long-term mechanical fixing for the finished board. Features: high-grade aluminum imitation effect, a super durable protection energy saving, high weather resistance, high self-cleaning, anti-pollution, acid rain, corrosion resistance, high decorative, low cost, convenient construction. Scope: office buildings, office buildings, banks, hotels, schools, hospitals, villas, high-end residential buildings and the like.